Service
Thermador control board replacement
A panel that does not respond, a board that fails its own memory check, or two boards that have stopped talking to each other. Tested before it is replaced, because boards are the most over-diagnosed part in this trade.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
Before you read on
What this job costs and how it is agreed
A starting figure, not a quote. What moves it is the model, how the unit is built in and which part it needs — settled after the on-site diagnostic.
Starts at
from $340
After a diagnostic from $95, which comes off the bill when you go ahead.
or call (305) 846-7685
Diagnostic
From $95, credited to the repair
The price
In writing, before anything is opened
Warranty
On the labor we performed
On the visit
How this visit actually goes
The same order every time, so nothing is opened and nothing is charged before you have seen the figure and said yes.
-
01
Establish it is the board
A dead panel is a supply problem as often as an electronics problem. Power at the appliance, then the connections, then the board — in that order, and not the other way round.
-
02
Read what it says about itself
These boards test their own memory at start-up and publish the result: E009 and E010 for the user interface, E309 and E310 for the control module. That narrows it to one of the two rather than "the electronics".
-
03
Check they are talking
E005 is not a broken board at all — it is the two boards having lost contact, and a connector left unseated after earlier work is a real cause.
-
04
Set the option code
A replacement board has to be told which model it belongs to, from the data plate. Skip it and the oven reports E000 and will not run — which looks exactly like a bad new part.
The money
What this usually costs in South Florida
The starting figure, the range the market quotes around it, and what pushes a job to either end.
-
Control board replacement cost
What a board costs, and the more useful question of whether it is really the board. On this make several conditions name the electronics explicitly, which makes an honest answer easier to reach.
- National range for mainstream boards: $150–$300
- Two boards on this equipment, and they fail separately
- The option code after a swap, which is easy to miss
Applies to
The Thermador units we carry this work out on
-
Masterpiece · Star-Sapphire · Crystal Dry Thermador dishwasher repair in Miami
Quiet, panel-ready, and dried by a mineral chamber rather than a heating element. Two of the commonest complaints about these machines are the design working exactly as intended; the third is a filter nobody has taken out in a year.
- Water standing in the tub after a cycle
- Plastics coming out wet
- The leak protection tripping and the machine refusing to run
-
Masterpiece · Professional · Steam · Speed Thermador wall oven repair in Miami
Built in at eye level, often two cavities in one cabinet, and increasingly one of the two is a steam oven with a water circuit of its own. "The oven is broken" almost always means one cavity of the pair, and which one narrows the job considerably.
- Not heating or not holding temperature
- The touch panel unresponsive after a long cycle
- The door locked after a self-clean
-
Professional · 30" 36" 48" 60" Thermador range repair in Miami
The appliance the brand is built around. A Professional range is two machines sharing a cabinet — a cooktop with star burners or an induction surface on top, and an oven underneath — and the two fail in completely different ways. Knowing which half you are describing shortens the visit before anybody arrives.
- A burner that clicks and will not light
- The oven not reaching or holding temperature
- The griddle heating unevenly across the plate
-
Freedom Induction · Masterpiece · Star burner Thermador cooktop repair in Miami
Freedom induction is this brand's own idea: one continuous glass surface that finds the pans rather than four printed rings to line them up with. It changes what goes wrong and what the complaint sounds like — most of what we are called out for on these is the surface protecting itself, and it is usually right to.
- A zone switching itself off mid-cook
- The surface not recognizing a pan
- Controls locked or answering a wet cloth
-
Freedom columns · French door · Under-counter Thermador refrigerator repair in Miami
A Freedom column is one cabinet holding one temperature — all refrigerator, no freezer in it — usually installed beside a freezer column as a matched pair behind panels that look like joinery. That makes the diagnosis cleaner and the access harder.
- Not holding temperature
- Frost or condensation inside the cabinet
- A door that no longer seals against its panel
In more detail
About Thermador control board replacement
Two boards, and they are not the same board
This equipment has a user interface — the panel you touch — and a control module, which is what actually switches elements and motors. They talk to each other, and the manufacturer publishes separate conditions for each: memory checks, temperature sensors on the boards themselves, and a communication error between them. Knowing which one is reporting is the difference between one part and two.
The step that gets missed
A replacement control module arrives generic and has to be set to the model it is going into, using the option code from the data plate. Without it the appliance reports a mismatched module and refuses to run. It is a two-minute step in service mode and it turns a "the new board is faulty" callback into a finished job.
What decides the figure
Which board, and what is in front of it. A dishwasher board behind a cabinet panel and an oven control module behind a professional trim are different amounts of time for the same soldered rectangle.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about thermador control board replacement
How do I know it is really the board?
Because it was tested rather than assumed. Boards are the most over-diagnosed part in appliance repair: a dead panel is often supply, a connector or a stuck key. On this make several conditions name the board explicitly, which makes the honest answer easier to reach.
My oven shows E000 after a repair.
That is the mismatched-module condition: a new board that has not been given its option code, read off the data plate. It is a setting rather than a part, and it is the whole fix.
Is a board worth replacing on an older appliance?
On a built-in oven or a panelled column, usually — the alternative is a replacement appliance plus cabinetry work. On a machine already needing other parts, we will tell you where the line is.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name